Linux version 2.6.7-1.494.2.2.pingo (igor@unije.camtp.uni-mb.si) (gcc version 3.3.3 20040412 (Red Hat Linux 3.3.3-7)) #1 Sat Aug 14 20:15:58 CEST 2004 BIOS-provided physical RAM map: BIOS-e820: 0000000000000000 - 000000000009f800 (usable) BIOS-e820: 000000000009f800 - 00000000000a0000 (reserved) BIOS-e820: 00000000000f0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fff0000 (usable) BIOS-e820: 000000001fff0000 - 000000001fff3000 (ACPI NVS) BIOS-e820: 000000001fff3000 - 0000000020000000 (ACPI data) BIOS-e820: 00000000fec00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 511MB LOWMEM available. zapping low mappings. On node 0 totalpages: 131056 DMA zone: 4096 pages, LIFO batch:1 Normal zone: 126960 pages, LIFO batch:16 HighMem zone: 0 pages, LIFO batch:1 DMI 2.3 present. ACPI: RSDP (v000 IntelR ) @ 0x000f7800 ACPI: RSDT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3000 ACPI: FADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff3040 ACPI: MADT (v001 IntelR AWRDACPI 0x42302e31 AWRD 0x00000000) @ 0x1fff7300 ACPI: DSDT (v001 INTELR AWRDACPI 0x00001000 MSFT 0x0100000e) @ 0x00000000 ACPI: PM-Timer IO Port: 0x408 Built 1 zonelists Kernel command line: ro root=LABEL=/ rhgb quiet mapped 4G/4G trampoline to ffff3000. Initializing CPU#0 CPU 0 irqstacks, hard=023c3000 soft=023c2000 PID hash table entries: 2048 (order 11: 16384 bytes) Detected 2807.285 MHz processor. Using tsc for high-res timesource Console: colour VGA+ 80x25 Dentry cache hash table entries: 131072 (order: 7, 524288 bytes) Inode-cache hash table entries: 65536 (order: 6, 262144 bytes) Memory: 515164k/524224k available (2008k kernel code, 8308k reserved, 651k data, 140k init, 0k highmem) Calibrating delay loop... 5537.79 BogoMIPS Security Scaffold v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode There is already a security framework initialized, register_security failed. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 (order: 0, 4096 bytes) CPU: After generic identify, caps: bfebfbff 00000000 00000000 00000000 CPU: After vendor identify, caps: bfebfbff 00000000 00000000 00000000 monitor/mwait feature present. using mwait in idle threads. CPU: Trace cache: 12K uops, L1 D cache: 16K CPU: L2 cache: 1024K CPU: After all inits, caps: bfebf3ff 00000000 00000000 00000080 Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. CPU0: Intel P4/Xeon Extended MCE MSRs (12) available CPU: Intel(R) Pentium(R) 4 CPU 2.80GHz stepping 03 Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Checking 'hlt' instruction... OK. checking if image is initramfs...it isn't (no cpio magic); looks like an initrd Freeing initrd memory: 190k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xfb9e0, last bus=2 PCI: Using configuration type 1 mtrr: v2.0 (20020519) ACPI: Subsystem revision 20040326 ACPI: IRQ9 SCI: Edge set to Level Trigger. ACPI: Interpreter enabled ACPI: Using PIC for interrupt routing ACPI: PCI Root Bridge [PCI0] (00:00) PCI: Probing PCI hardware (bus 00) PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.1 PCI: Transparent bridge - 0000:00:1e.0 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.HUB0._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 9 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 *5 7 9 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK0] (IRQs 3 4 5 7 9 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNK1] (IRQs 3 4 5 7 9 10 *11 12 14 15) Linux Plug and Play Support v0.97 (c) Adam Belay usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing ACPI: PCI Interrupt Link [LNKA] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKD] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKC] enabled at IRQ 5 ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNK1] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5 ACPI: PCI Interrupt Link [LNKB] enabled at IRQ 11 ACPI: PCI interrupt 0000:00:1f.3[B] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI interrupt 0000:00:1f.5[B] -> GSI 11 (level, low) -> IRQ 11 ACPI: PCI Interrupt Link [LNKE] enabled at IRQ 5 ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 5 (level, low) -> IRQ 5 TC classifier action (bugs to netdev@oss.sgi.com cc hadi@cyberus.ca) vesafb: probe of vesafb0 failed with error -6 apm: BIOS version 1.2 Flags 0x07 (Driver version 1.16ac) apm: overridden by ACPI. audit: initializing netlink socket (disabled) audit(1094726821.756:0): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API ksign: Installing public key data Loading keyring - Added public key 2568877FC1F55722 - User ID: Red Hat, Inc. (Kernel Module GPG key) ksign: invalid packet (ctb=00) Unable to load default keyring: error=74 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: Fan [FAN] (on) ACPI: Processor [CPU0] (supports C1) ACPI: Thermal Zone [THRM] (59 C) isapnp: Scanning for PnP cards... isapnp: No Plug & Play device found Real Time Clock Driver v1.12 Linux agpgart interface v0.100 (c) Dave Jones agpgart: Detected an Intel 865 Chipset. agpgart: Maximum main memory to use for agp memory: 439M agpgart: AGP aperture is 128M @ 0xe8000000 Serial: 8250/16550 driver $Revision: 1.2 $ 8 ports, IRQ sharing enabled ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A RAMDISK driver initialized: 16 RAM disks of 16384K size 1024 blocksize divert: not allocating divert_blk for non-ethernet device lo Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx ICH5: IDE controller at PCI slot 0000:00:1f.1 ACPI: PCI interrupt 0000:00:1f.1[A] -> GSI 5 (level, low) -> IRQ 5 ICH5: chipset revision 2 ICH5: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:DMA, hdb:pio ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:DMA, hdd:DMA hda: WDC WD1200BB-00FTA0, ATA DISK drive Using cfq io scheduler ide0 at 0x1f0-0x1f7,0x3f6 on irq 14 hdc: SAMSUNG DVD-ROM SD-616E, ATAPI CD/DVD-ROM drive hdd: LITE-ON DVDRW SOHW-1213S, ATAPI CD/DVD-ROM drive ide1 at 0x170-0x177,0x376 on irq 15 hda: max request size: 1024KiB hda: 234441648 sectors (120034 MB) w/2048KiB Cache, CHS=16383/255/63, UDMA(100) hda: hda1 hda2 hda3 hdc: ATAPI 48X DVD-ROM drive, 512kB Cache, UDMA(33) Uniform CD-ROM driver Revision: 3.20 hdd: ATAPI 48X DVD-ROM DVD-R CD-R/RW drive, 2048kB Cache, UDMA(33) ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.0:USB HID core driver mice: PS/2 mouse device common for all mice serio: i8042 AUX port at 0x60,0x64 irq 12 serio: i8042 KBD port at 0x60,0x64 irq 1 input: AT Translated Set 2 keyboard on isa0060/serio0 md: md driver 0.90.0 MAX_MD_DEVS=256, MD_SB_DISKS=27 NET: Registered protocol family 2 IP: routing cache hash table of 1024 buckets, 32Kbytes TCP: Hash tables configured (established 32768 bind 9362) Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S1 S4 S5) md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. RAMDISK: Compressed image found at block 0 VFS: Mounted root (ext2 filesystem). kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. Freeing unused kernel memory: 140k freed SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks ACPI: Power Button (FF) [PWRF] ACPI: PCI interrupt 0000:00:1d.7[D] -> GSI 11 (level, low) -> IRQ 11 ehci_hcd 0000:00:1d.7: EHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.7 to 64 ehci_hcd 0000:00:1d.7: irq 11, pci mem 22842000 ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1 PCI: cache line size of 128 is not supported by device 0000:00:1d.7 ehci_hcd 0000:00:1d.7: USB 2.0 enabled, EHCI 1.00, driver 2004-May-10 hub 1-0:1.0: USB hub found hub 1-0:1.0: 8 ports detected USB Universal Host Controller Interface driver v2.2 ACPI: PCI interrupt 0000:00:1d.0[A] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:1d.0: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.0 to 64 uhci_hcd 0000:00:1d.0: irq 5, io base 0000cc00 uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2 hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.1[B] -> GSI 11 (level, low) -> IRQ 11 uhci_hcd 0000:00:1d.1: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.1 to 64 uhci_hcd 0000:00:1d.1: irq 11, io base 0000c000 uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3 hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.2[C] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:1d.2: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.2 to 64 uhci_hcd 0000:00:1d.2: irq 5, io base 0000c400 uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4 hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI interrupt 0000:00:1d.3[A] -> GSI 5 (level, low) -> IRQ 5 uhci_hcd 0000:00:1d.3: UHCI Host Controller PCI: Setting latency timer of device 0000:00:1d.3 to 64 uhci_hcd 0000:00:1d.3: irq 5, io base 0000c800 uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5 hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected EXT3 FS on hda1, internal journal device-mapper: 4.1.0-ioctl (2003-12-10) initialised: dm@uk.sistina.com cdrom: open failed. cdrom: open failed. Adding 1606492k swap on /dev/hda2. Priority:-1 extents:1 kjournald starting. Commit interval 5 seconds EXT3 FS on hda3, internal journal EXT3-fs: mounted filesystem with ordered data mode. IA-32 Microcode Update Driver: v1.14 microcode: No new microdata for cpu 0 parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected SCSI subsystem initialized inserting floppy driver for 2.6.7-1.494.2.2.pingo Floppy drive(s): fd0 is 1.44M FDC 0 is a post-1991 82077 Linux Tulip driver version 1.1.13 (May 11, 2002) ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 5 (level, low) -> IRQ 5 tulip0: MII transceiver #1 config 3100 status 7869 advertising 05e1. divert: allocating divert_blk for eth0 eth0: ADMtek Comet rev 49 at 0x2284c000, 00:0A:48:09:3C:8C, IRQ 5. divert: freeing divert_blk for eth0 ip_tables: (C) 2000-2002 Netfilter core team Linux Tulip driver version 1.1.13 (May 11, 2002) ACPI: PCI interrupt 0000:02:00.0[A] -> GSI 5 (level, low) -> IRQ 5 tulip0: MII transceiver #1 config 1000 status 786d advertising 05e1. divert: allocating divert_blk for eth0 eth0: ADMtek Comet rev 49 at 0x2284c000, 00:0A:48:09:3C:8C, IRQ 5. ip_tables: (C) 2000-2002 Netfilter core team eth0: Setting full-duplex based on MII#1 link partner capability of 45e1. parport0: PC-style at 0x378 (0x778) [PCSPP,TRISTATE,EPP] parport0: irq 7 detected lp0: using parport0 (polling). lp0: console ready NET: Registered protocol family 10 Disabled Privacy Extensions on device 0235b140(lo) IPv6 over IPv4 tunneling driver divert: not allocating divert_blk for non-ethernet device sit0 input: ImPS/2 Generic Wheel Mouse on isa0060/serio1 eth0: no IPv6 routers present psmouse.c: bad data from KBC - timeout process `talk' is using obsolete setsockopt SO_BSDCOMPAT